Digital Monitoring Products 1912XR Guia de Instalação descarregar pdf (Página 24)

Digital Monitoring Products, Inc. 1912XR Installation Guide

Page 24

1912XR Installation Guide

26.3 Multiple Indicating circuit modules for zoned annunciation

Auxiliary Power

Ground

Alarm Input

Bell Power Input

Bell Output +

Bell Output -

Bell Trouble

24 VDC 5 Amp

Maximum

Power Supply

Trouble Contacts

N/C

Zone 2 Indicating Circuit

Module.

DMP Model 866

37mA at 12 VDC

The Auxiliary Power Supply and Indicating

Circuit Module trouble contact Loop must

be programmed as a Supervisory Type Loop

and must be selected for display in the

keypad status list.

See section 10.6 in the 1912XR

Programming Manual (LT-0171).

NOTE: If an auxiliary supply is

not used, terminals 3 and 4 on the

866 Indicating Circuit Module

can be jumpered together to

supply bell power from the

1912XR panel.

A maximum of 1 Amp at 12 VDC

is available from terminal 5 of

the 1912XR.

Auxiliary power supplies must be

regulated UL listed for Fire Protection

Signaling Service. Power supplies

must have battery backup.

Auxiliary Power

Ground

Alarm Input

Bell Power Input

Bell Output +

Bell Output -

Bell Trouble

UL Listed, Polarized

Indicating Devices.

10k Ω EOL Resistor

DMP Model 308

AUXILIARY

POWER

SUPPLY

AUXILIARY

POWER

SUPPLY

10k Ω EOL Resistor

DMP Model 308

BELL

4567

GND

REDB -

389

14 15

17 18 19

YEL GRN BLKB + SMK L5+ L5- L1 L2 L3 L4GNDGND

1k Ω

3.3k Ω Resistor

DMP Model 309

1k Ω 1k Ω

Dual Line Expansion

J10

Battery Only Restart

J16

Command Processor Reset

Auxiliary Power

Ground

Alarm Input

Bell Power Input

Bell Output +

Bell Output -

Bell Trouble

UL Listed, Polarized

Indicating Devices.

10k Ω EOL Resistor

DMP Model 308

AUXILIARY

POWER

SUPPLY

24 VDC 5 Amp

Maximum

24 VDC 5 Amp

Maximum

You can have up to sixteen 866

Indicating Circuit Modules by using

the relay outputs available on the

1912XR panel.

All modules must be installed within

an approved enclosure connected

by conduit.

Zone 1 Indicating Circuit

Module. DMP Model 866

37mA at 12 VDC

Common

Indicating Circuit Module

DMP Model 866

37mA at 12 VDC

EPROM Socket

To additional Zone 1

Indicating Circuit Modules.

To additional Zone 2

indicating circuit modules.

Zone 1

Output

Zone 2

Output

Each 866 Indicating Circuit

Module in alarm draws up to

35mA from its terminal 3 alarm

input.

J15

Connects auxiliary

power to common

of Relay Output 1.

Relay Output 1

Model 305 required.

Relay Output 2

Model 305 required.

Relay Outputs 1 and 2

combined can provide

up to 600mA at 12 VDC

of panel auxiliary power.

Outputs 3 to 6 can

provide up to 50mA

each at 12 VDC. This

is sufficient for one

866 module per

indicating zone 3 to 6.

Relay 1

N/O

Orange

Relay 2

Common

Gray

Relay 2

N/O

Orange

Model 304

Output Harness

1k Ω

1 2 ... 19 20 21 22 23 24 25 26 27 28 29 ... 35 36

Comentários a estes Manuais

Sem comentários

Digital Monitoring Products 1912XR Guia de Instalação Página 24

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digital Monitoring Products 1912XR