Digital Monitoring Products Canadain XR500 Manual de Instruções descarregar pdf (Página 37)

XR500 Series Programming Guide Digital Monitoring Products

SyStem OptiOnS

9.6

CRS ZONE TM: 4

Cross Zone Time

Enter the time allowed between zone faults. When zones are cross zoned, the same zone

or a second cross zoned zone must fault within this time in order for an alarm report for

both zones to be sent to the receiver. If the cross zone time expires without the second

zone faulting, only a zone fault from the rst zone is reported. Cross-zone time can be

from 4 to 250 seconds. Entering 0 (zero) disables this function. Default is 4. See the

Appendix.

9.7

RETARD DELAY: 10

Zone Retard Delay

Enter the retard time assigned to Fire, Supervisory, Auxiliary 1, Auxiliary 2, Arming, and

Panic type zones. The retard delay only functions when the zone is shorted. The zone

must remain shorted for the entire length of the Retard Delay before being recognized

by the panel. The Zone Retard Delay can be from 1 to 250 seconds. Entering a 0 (zero)

disables this function.

9.8

PWR FAIL HRS: 1

Power Fail Delay

This option tracks the duration of an AC power failure. When the AC power is off for the

length of the programmed delay time, an AC power failure report is sent to the receiver.

The delay time can be from 1 to 15 hours. Entering a 0 (zero) sends the power failure

report after a 15-second delay. The default setting is 1.

Note: For UL burglary installations Power Fail Delay shall be programmed to 0 (zero).

Note: For UL re installations, Power Fail Delay shall be programmed as required

by the service of the panel. For Central Station service: 6-12, for Remote Station

service: 12-15.

9.9

SWGRBYPS TRIPS: 2

Swinger Bypass Trips

Enter the number of times (1-6) a zone can go into an alarm or trouble condition within

one hour be fore being auto matically bypassed. Bypassed zones are auto matically reset

when the area they are assigned to is disarmed. All 24-hour zones are reset when any

area of the system is dis armed. A programming Stop operation restores a bypassed zone.

Entering 0 (zero) disables this function. Default is 2.

How it works

The panel hour timer starts at 59 minutes past the hour. If the hour timer expires before

the trip counter is exceeded, the trip counter returns to 0 (zero). If the trip counter is

exceeded before the hour expires, the zone is auto matically bypassed by the panel. A

Bypass Re port is sent to the receiver if Bypass Re ports is YES.

Note: Not investigated by UL.

9.10

RST SBYP NO YES

Reset Swinger Bypass

When YES is selected, an auto matically bypassed zone is reset if it remains in a normal

condition for one complete hour after being bypassed. A report of the automatic reset is

sent to the receiver if Bypass Reports has been se lected as YES. Default is NO.

Note: Not investigated by UL.

9.11

TIME CHG NO YES

Time Zone Changes

This function allows the panel to request automatic time changes from the

DMP SCS-1R Receiver on Path 1. For the receiver to send time changes, it must be

programmed to send time changes and must be receiving time change updates from the

network automation computer at least every 24 hours. Default is YES.

HRS FROM GMT: 6

When time zone is programmed YES, enter the number (0-23) that indicates the

Greenwich Time zone (GMT) where the panel is located. The default is 6.

1 2 ... 32 33 34 35 36 37 38 39 40 41 42 ... 83 84

Comentários a estes Manuais

Sem comentários

Digital Monitoring Products Canadain XR500 Manual de Instruções Página 37

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digital Monitoring Products Canadain XR500