Digital Monitoring Products Canadian XR100 Guia de Instalação descarregar pdf (Página 9)

Digital Monitoring Products XR100 Series Installation Guide

REVISIONS

XR100 Series Installation Guide Digital Monitoring Products

INTRODUCTION

Product Specications

1.1 Power Supply

Transformer Input: Model 327, plug-in — Primary input: 120 VAC, 60 Hz, Secondary output: 16.5 VAC 50 VA

Model 322, wire-in — Primary input: 120 VAC, 60 Hz, Secondary output: 16 VAC 56 VA

Standby Battery: 12 VDC, 1.0 Amps Max. charging current

Models 365, 366, 367, 368, or 369

Replace every 3 to 5 years

* Auxiliary: 12 VDC output at 1.5 Amp Max

* Bell Output: 12 VDC at 1.5 Amp Max

Note: The combined Auxiliary and Bell outputs total cannot exceed 3 Amps with a 50 VA or 56 VA Transformer.

All circuits are inherent Power Limited except the red battery wire and AC terminal.

* For UL installations, the total current combined from Auxiliary and Bell Power cannot exceed:

1.3 Amps with a 50 VA transformer, 1.0 Amp Max for Auxiliary Power

1.9 Amps with a 56 VA transformer, 1.0 Amp Max for Auxiliary Power and 1.5 Amp Max for Bell

1.2 Communication

Built-in network communication to DMP Model SCS-1/SCS-1R Receivers (XR100N only)

Built-in dialer communication to DMP Model SCS-1/SCS-1R Receivers

Built-in Contact ID communication to non-DMP receivers

Optional 893A Dual Phone Line Module with phone line supervision

Can operate as a local panel

1.3 Panel Zones

Eight 1k Ohm EOL burglary zones (zones 1 to 8)

Two 3.3k Ohm EOL powered zone with reset (zones 9 and 10)

1.4 Keypad Bus

You can connect up to eight of the following supervised keypads and expansion modules to the keypad bus:

• Alphanumeric keypads • Four- and/or single-zone expansion modules

• Single-zone detectors • Access control modules

1.5 LX-Bus™

You can connect the following devices to the LX-Bus™ provided on the panel. See Accessory Devices in section 3.4.

• Four- and/or single-zone expansion modules • Single-zone detectors

• Relay output expansion modules • Graphic annunciator modules

1.6 Outputs

The XR100 Series provide two Single Pole, Double Throw (SPDT) relay outputs which require the installation of two

Model 305 relays, each rated 1 Amp at 30 VDC resistive (power limited sources only). A Model 431 Output Harness is

required to use these outputs.

The XR100 Series panels also provide four open collector outputs rated for 50mA each. The open collector outputs

provide ground connection for a positive voltage source. A Model 300 Output Harness is required to use these

outputs.

1.7 Enclosure Specications

The XR100 Series panels are shipped in an enclosure with a transformer, End-of-Line resistors, battery leads, user’s

guide, and programming sheets.

Model 350A Enclosure

Enclosure size: 17.5” W x 13.5” H x 3.75” D

Color: Gray (G)

Construction: 18-gauge with 16-gauge door

Model 350 Enclosure

Enclosure size: 17.5” W x 13.5” H x 3.5” D

Color: Gray (G) or Red (R)

Construction: 18-gauge, cold-rolled steel

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 45 46

Comentários a estes Manuais

Sem comentários

Digital Monitoring Products Canadian XR100 Guia de Instalação Página 9

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digital Monitoring Products Canadian XR100