Digital Monitoring Products XR20 Guia de Instalação descarregar pdf (Página 23)

XRSuper6/XR20/XR40 Installation Guide Digital Monitoring Products

ComplIanCe

ANSI/UL 365 Specications

Police Station Connected Systems

20.1 Entry Delay

The maximum entry delay must not exceed 60 seconds with the Model 350A housing. See LT-0305.

20.2 Bell

A local audible signal appliance must be used.

The alarm housing for a mercantile alarm system without a remote alarm transmission connection shall be

mounted on the outside of the building, visible from a public street or highway. It shall be accessible for

examination and repair. It shall also be located not more than four stories above the street level unless:

a) A second alarm sounding device and housing, intended for outside service, is mounted adjacent to the

premises or area of the building in which the alarm system is installed or

b) A second alarm sounding device, intended for inside service, is mounted within the premises.

In either case, the outside alarm sounding device and housing may be mounted as high as the seventh oor.

20.3 Bell Cutoff

The bell cutoff time cannot be less than 15 minutes. See the Programming Guide (LT-0305).

20.4 Automatic Bell Test

The Automatic Bell Test option must be programmed as YES. See the Programming Guide (LT-0305).

20.5 Mercantile

For Mercantile and Police Station Connect operation the XRSuper6/XR20/XR40 panel and all standby

batteries must be mounted in an attack resistant housing (DMP Model 350A).

20.6 Mercantile Safe and Vault

When the DMP Model 350A housing is used, the panel provides operation as a mercantile safe and vault

alarm. Bell Supervision and wiring must be in accordance with UL 681. If the panel is mounted outside the

safe or vault, tamper protection and the Sentrol Model 5402 or Potter EVD listed vibration detectors should

be used. The XRSuper6/XR20/XR40 does not provide operation as a Bank Safe and vault alarm.

20.7 Line Security for Police Connect

Basic line security is provided when the Model XRSuper6/XR20/XR40 is congured as a dialer system.

20.8 Standard Line Network Security

Standard Line Security is provided when congured as a NET system using an XRSuper6, XR20, or XR40 panel

with an iCOMSL™ Network Alarm Router. The NET Check-in time must be set from 01 to 06 minutes. When a

dialer is required for 06 minute check-in time, an attack resistant enclosure (DMP Model 350A) is required.

When the check-in time is set to a number less than 200 seconds (1, 2, or 3 minutes), an attack resistant

enclosure is not required. See the Communication section of the XRSuper6, XR20, XR40 Programming Guide

(LT-0305).

20.9 Wireless Arming Mode

The System Options Mode for arming must be programmed as Area or All/Perimeter (A/P). See the

XRSuper6/XR20/XR40 Programming Guide (LT-0305).

20.10 Wireless Tamper

The Zone Information Disarmed Open Message to Transmit must be programmed Trouble (T). See the

XRSuper6/XR20/XR40 Programming Guide (LT-0305).

20.11 Wireless External Contact

When used, the External Contact of 1101, 1102, or 1103 must be programmed Normally Closed. See the

XRSuper6/XR20/XR40 Programming Guide (LT-0305).

20.12 Wireless Supervision Time

The Zone Information Supervision Time cannot be set to 0 (zero). See the XRSuper6, XR20, XR40

Programming Guide (LT-0305).

20.13 Wireless Audible Annunciation

The Wireless Audible option must be selected as ANY for commercial applications.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 29 30 31

Comentários a estes Manuais

Sem comentários

Digital Monitoring Products XR20 Guia de Instalação Página 23

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digital Monitoring Products XR20

Relacionado con productos y manuales para No Electrolux EOB3430COK