Digital Monitoring Products XT50 Guia de Instalação descarregar pdf (Página 42)

XT Series Programming Guide Digital Monitoring Products

ZONE INFORMATION

14.12.1 Message To Transmit

You can send two report types to the receiver: Alarm and Trouble. These are represented

by the characters A and T. Press any Select key to display the zone report options.

ALARM - Selecting A allows an alarm report to be sent to the receiver and the bell output

to activate according to zone type. See the Bell Action section. The zone name appears

in the panel’s alarmed zones status lists.

TROUBLE - Selecting T allows a trouble report to be sent to the receiver and the zone

name to appear in the panel’s alarmed zones status lists.

LOCAL - When you select L, an alarm report is NOT sent to the receiver. The bell output

still activates according to zone type and the zone name appears in the panel’s alarmed

zones status lists.

– (dash) - When you select – , reports are NOT sent to the receiver. The bell output does

not activate and there is no display in the panel’s alarmed zones status list. Only the

programmed Output Number activates.

14.12.2 Output Number

You can specify any of the outputs/Favorites on the XT30/XT50 to be activated by a zone

condition. The output/Favorite can be activated regardless of the report to transmit or

whether or not the zone is programmed as local. An output activated by a non-24-hour

armed zone is turned off when the zone’s area is disarmed by a user.

To enter an Output Number, press any Select key followed by the output number 1 to 4,

31-34, 41-44, or F1-F20. Press the COMMAND key.

14.12.3 Output Action

Entering an Output Number displays this option that allows you to assign an output

action to the relay. A description of the available output actions is given below:

STEADY - The output is turned on and remains on until the area is disarmed, an output

cutoff time expires, or the output is reset from the keypad User Menu.

PULSE - The output alternates one second on and one second off until the area is

disarmed, an output cutoff time expires, or the output is reset from the keypad User

Menu.

MOMENTARY - The output is turned on only once for one second.

FOLLOW - The output is turned on and remains on while the zone is in an off normal, or

bad condition. When the zone restores, the output is turned off.

After you have selected the Message To Transmit, the display prompts you for the same

three selections for Disarmed Short, Armed Open, and Armed Short conditions. If the

zone is a 24-hour type, only the Armed Open and Armed Short conditions are displayed.

When you have programmed all of the zone conditions, the Swinger Bypass selection is

then dis played.

14.13 Swinger Bypass

Selecting YES allows the zone to be swinger bypassed by the panel according to the

programming in Swinger Bypass Trips and Reset Swinger Bypass. The Bypassed zone

displays in the keypad Status List. Selecting NO disables swinger bypassing for this zone.

How it works

If within one hour, a zone trips the total number of times as specied in Swinger Bypass

Trips, the panel bypasses it until the following conditions occur; the area in which

the zone is assigned is disarmed, the zone is manually reset through the Bypass Zones

keypad User Menu function, the zone remains normal for one hour and the Reset Swinger

Bypass is YES.

If the zone trips fewer than the specied times within one hour of the rst trip, the

bypass trip counter returns to 0 (zero) and the process must be repeated.

A report of the swinger bypass is sent to the receiver if Bypass Reports is YES.

MSG: TROUBLE

A T L -

OUTPUT NO: 0

ACTION:

STD PLS MOM FOLW

SWGR BYP NO YES

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 ... 54 55

Comentários a estes Manuais

Sem comentários

Digital Monitoring Products XT50 Guia de Instalação Página 42

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digital Monitoring Products XT50