Digital Monitoring Products XT50 Guia de Instalação descarregar pdf (Página 49)

Digital Monitoring Products XT Series Programming Guide

APPENDIX

Walk Test

To conduct the Walk Test, reset the control panel by momentarily placing a jumper on

J16 then wait one minute. From the keypad, enter the code 8144. The keypad displays

WALK TEST. If the system is monitored and the communication type is DD or NET, the

system sends a System Test Begin report to the central station. All programmed zones

are included in the test.STD (Standard Walk Test) - Select STD to Walk test zones. All

programmed zones are included in the test.

WLS (Wireless Check-in Test) - Select WLS to automatically test 1100 Series wireless

transmitter communications. Includes all wireless devices except key fobs and

transmitters programmed for a supervision time of 0 (zero).

Note: For the XT30, Wireless Check-in Test operation only displays when connected to

1100D Wireless Receiver Version 105 or higher.

PIR (Wireless PIR Walk Test) - The PIR Walk Test allows the installer to verify the 1126

operation. When enabled, the 1126 or 1127 LED ashes each time motion is detected

for up to 30 minutes. This is a local test only and no messages are sent to the Central

Station.

Trip Counter for Walk Test (STD)

Displays the number of zone trips during the Walk Test.

• Each time a selected zone trips, the keypad buzzes and the bell rings for two

seconds.

• Each time a FI, FV, or SV zone trips, a Sensor Reset occurs.

END - Press the Select key directly below END to stop the Walk Test. When the Walk Test

ends or a 20 minute time-out expires, a nal Sensor Reset occurs. The System Test End

message is sent to the receiver along with Verify and Fail messages for each zone under

test. Faulted zones then display on the keypad.

Trip Counter For DMP Wireless Check-in Test (WLS)

Displays the number of wireless zones that automatically communicate a supervisory

check-in message.

• The number of zones that check in. (XX in the example).

• The total number of wireless zones programmed for supervision that should check

in. (ZZ in the example).

END - Select END to stop the Wireless Check-in Test. When the test ends or a 20-minute

time-out expires, normal wireless zone processing returns. If all transmitters check-in,

both numbers will match within three (3) minutes. If a transmitter has multiple zones

(1101, 1114, etc.), all zones will be included in the counts. Failed wireless zones will

then display on the keypad.

Test End Warning

When no zones have been tripped and ve minutes remain on the 20 minute Walk Test

timer, the keypad displays TEST END WARNING and the keypad tones. If no additional

test zone trips occur, the test ends and a nal Sensor Reset automatically occurs. The

System Test End message is sent to the receiver along with Verify and Fail messages for

each zone under WALK test. Faulted zones then display on the keypad.

Failed Zones Display

Each zone that did not trip at least once during the Walk Test displays on the keypad

that initiated the test. Any Fire (FI) Panic (PN) or Supervisory (SV) 24-hour zone that is

faulted at the end of the Walk Test displays a trouble condition for that zone regardless

of the message programmed for the open or short condition of the zone and a zone

trouble is sent to the receiver. Press the COMMAND key to display the next failed zone

For the Wireless Check-in Test, failed wireless zones display only on the keypad. Zone

Verify/Fail reports are not sent to the central station receiver for the wireless checkin

test.

WALK TEST

STD WLS PIR

WALK TEST

TRIPS: XXX END

WIRELESS TEST

CHKIN: XX/ZZ END

TEST END WARNING

SOUTH LOBBY

ZONE: 10 -FAIL

1 2 ... 44 45 46 47 48 49 50 51 52 53 54 55

Comentários a estes Manuais

Sem comentários

Digital Monitoring Products XT50 Guia de Instalação Página 49

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digital Monitoring Products XT50