Digital Monitoring Products XTL Series Guia de Instalação descarregar pdf (Página 42)

XTL/XTLC Programming Guide Digital Monitoring Products

APPENDIX

16.5 Using the 984 Command Function

This feature allows

the integrity of the cellular communication to be tested.

NBR:

Not available for XTL/XTLC panels. If selected the keypad displays NO DIALER.

TEST: This option tests each function of the panel’s cellular communication. The tests proceed until a function

does not pass, or until all have been tested with positive results. The progress displays during each test.

PICKUP: Not available for XTL/XTLC panels. If selected the keypad displays NO DIALER.

16.6 Using the Walk Test

The XTL/XTLC panel provides a walk test feature that allows a single technician to test all the protection

devices connected to zones on the system. Conduct the Walk Test within 30 minutes of resetting the panel. The

Walk Test automatically ends if no zones are tripped for 20 minutes. TEST IN PROGRESS displays at all keypads.

When ve minutes remain, TEST END WARNING displays. If any areas are armed the Walk Test does not start

and SYSTEM ARMED displays.

Walk Test

To conduct the Walk Test, reset the control panel by pressing the reset button then wait

one minute. From the keypad, enter the code 8144. The keypad displays WALK TEST.

WLS (Wireless Check-in Test) - Select WLS to automatically test 1100 Series wireless

transmitter communications. Includes all wireless devices except key fobs and

transmitters programmed for a supervision time of 0 (zero).

PIR (Wireless PIR Walk Test) - The PIR Walk Test allows the installer to verify the 1126 and

1127 operation. When enabled, the 1126 LED ashes each time motion is detected for up to

30 minutes. This is a local test only and no messages are sent to the Central Station.

Trip Counter For DMP Wireless Check-in Test (WLS)

Displays the number of wireless zones that automatically communicate a supervisory

check-in message.

•The number of zones that check in. (XX in the example).

•The total number of wireless zones programmed for supervision that should check in.

(ZZ in the example).

END - Select END to stop the Wireless Check-in Test. When the test ends or a 20-minute

time-out expires, normal wireless zone processing returns. If all transmitters check-in,

both numbers will match within three (3) minutes. If a transmitter has multiple zones

(1101, 1114, etc.), all zones will be included in the counts. Failed wireless zones then

display on the keypad.

Test End Warning

When no zones have been tripped and ve minutes remain on the 20 minute Walk Test

timer, the keypad displays TEST END WARNING and the keypad tones. If no additional test

zone trips occur, the test ends and a nal Sensor Reset automatically occurs. The System

Test End message is sent to the receiver along with Verify and Fail messages for each zone

under WALK test. Faulted zones then display on the keypad.

Failed Zones Display

Each zone that did not trip at least once during the Walk Test displays on the keypad that

initiated the test. Any Fire (FI) Panic (PN) or Supervisory (SV) 24-hour zone that is faulted at

the end of the Walk Test displays a trouble condition for that zone regardless of the message

programmed for the open or short condition of the zone and a zone trouble is sent to the

receiver. Press the COMMAND key to display the next failed zone.

For the Wireless Check-in Test, failed wireless zones display only on the keypad. Zone

Verify/Fail reports are not sent to the central station receiver for the wireless checkin

test.

WALK TEST

STD WLS PIR

WALK TEST

TRIPS: XXX END

TEST END WARNING

SOUTH LOBBY

ZONE: 10 -FAIL

1 2 ... 37 38 39 40 41 42 43 44 45 46 47 48 49

Comentários a estes Manuais

Sem comentários

Digital Monitoring Products XTL Series Guia de Instalação Página 42

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digital Monitoring Products XTL Series