Digital Monitoring Products XR20 Guia de Instalação descarregar pdf (Página 23)

XRSuper6/XR20/XR40 Programming Guide Digital Monitoring Products

SySTem oPTionS

System Options

6.1

SYSTEM OPTIONS

System Options

This section allows you to select system wide parameters used in the operation of

the XRSuper6/XR20/XR40 system. A description of each System Option follows:

6.2

MODE: ALL/PERIM

AREA A/P H/A

Mode

This congures the panel as either a four Area system (XR20/XR40 only), an All/

Perimeter system (Perimeter/Interior), or a Home/Away system (Perimeter, Interior,

and Bedrooms). Zones must be assigned to Bedrooms for the area to be active.

When using wireless zones for an Area (XR20/XR40 only) or All/Perimeter system,

the keypad trouble buzzer resounds every four hours when wireless zone trouble or

wireless low battery is displayed.

Unvacated Premise

When arming AWAY or ALL from a keypad at a system programmed for All/Perimeter

or Home/Away, and no exit type zone is faulted during Exit Delay (the exit door is

not opened to leave after arming), the system arms as HOME or PERIM by disarming

the interior areas including bedrooms at the end of the delay.

6.3

CLS CODE NO YES

Closing Code

When YES is selected, a code number is required for system arming. If NO is

selected, a code number is not required for system arming. Default is NO.

6.4

CLS CHK NO YES

Closing Check (XR20/XR40 Only)

Select YES to enable the panel to verify that all areas have been armed after a

schedule expires. If the Closing Check nds any areas disarmed past the scheduled

time, all keypads emit a steady beep and display CLOSING TIME!. Default is NO.

All zones in that area are delayed along with the Exit zone. Entry Delay times can

be from 30 to 250 seconds. Repeat the above for each entry delay being used in the

system.

6.5

ENTRY DELAY 1: 30

ENTRY DELAY 2: 60

Entry Delay 1

Enter the entry delay time for all exit type zones programmed to use Entry Delay 1.

When an armed Exit type zone is faulted, the keypad prewarn tone begins sounding.

ENTER CODE:- and the name of the zone causing the Entry Delay displays on all

keypads.

When the rst digit of a code is entered, the prewarn tone stops at the keypad.

If, within ve seconds, a valid user code is not entered or an invalid user code is

entered, the prewarn tone begins sounding again. Fifteen seconds must elapse

before entering a digit silences the prewarn tone again.

Note: When the SIA CP-01 option in System Options is set to NO, the rst digit

entered at the keypad does not stop the prewarn tone.

The area must be disarmed before the entry delay expires or an Alarm Message is

sent to the receiver and an alarm sounds. All Burglary type zones in all areas are

delayed along with the Exit zone.

Entry delay times can be from 30 to 250 seconds. Repeat the above for Entry Delay

2 if it is being used. Default is 30 seconds for Entry Delay 1.

Note: Specic Exit Error operation is based on the Entry Delay used (1 or 2) with an

EX type zone. See Exit Delay.

Note: For UL Installations, the combined Transmit Delay (Abort Window) and

Entry Delay must not exceed one (1) minute.

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 51 52

Comentários a estes Manuais

Sem comentários

Digital Monitoring Products XR20 Guia de Instalação Página 23

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digital Monitoring Products XR20