Digital Monitoring Products XR20 Guia de Instalação descarregar pdf (Página 39)

XRSuper6/XR20/XR40 Programming Guide Digital Monitoring Products

zone informaTion

11.10.8

PRESS TIME: XXXXX

Button Press Time

This option species the amount of time (SHORT or LONG) the user must press the

button before the key fob sends a message to the wireless receiver. The default

press time displays. Press any Select key to set the Button Press Time for Arm,

Disarm, Toggle, Status, Output, and Sensor Reset.

Note: The Button Press Time is not programmable on Panic (PN or PN2), Emergency

(EM or EM2) or Unused (UN) zones. For those zones the button press time is always

two (2) seconds.

SHORT LONG

SHORT - Press the button for one-half (1/2) second to send the message to the

wireless receiver.

LONG - Press the button for two (2) seconds to send the message to the wireless

receiver.

11.10.9

AREA: 1 2 3 4

Arm/Disarm Area Selection

For XR20 or XR40 Area systems, enter the areas, 1 to 4, to be armed/disarmed by

the Key Fob button being programmed.

On XRSuper6, XR20, or XR40 panels

ARM AREAS: PERIM

This species the area to be armed by the Key Fob button being programmed.

For All/Perimeter systems, choose PERIM or ALL.

For Home/Sleep/Away or Home/Away systems, choose HOME, SLEEP, or AWAY.

After selecting the areas, for one-button key fobs the Zone No.: prompt displays.

For two-button or four-button key fobs, the Key Fob Button Selection option

displays to program additional buttons.

11.10.10

OUTPUT NO: 0

Output Number

You can specify a relay output to operate when OUT (Output), PN (Panic), PN2

(Panic 2), EM (Emergency), or EM2 (Emergency 2) is selected for a key fob Button

Action and the button is pressed. Valid range is 1 to 4. For an output turned on

by a PN, PN2, EM, or EM2 button action, the output turns off when any area is

disarmed.

To enter an output number, press a top row Select key followed by the output

number. Press the COMMAND key.

11.10.11

ACTION:

Output Action

This option allows you to dene the output action (STD, PLS, MOM, TGL, OFF) for

the selected output number. The default is Steady.

STD PLS MOM TGL

STD (Steady) - The output is turned on and remains on.

PLS (Pulse) - The output alternates one second on and one second off.

MOM (Momentary) - The output is turned on only once for one second.

TGL (Toggle) - The output alternates between the on state and off state. Each

button press toggles the output state.

OFF

OFF (Off) - The output is turned off. If programmed, the output was turned on by

some other means such as another button press, a zone action, or a schedule.

Note: When the output is assigned to PN/PN2 or EM/EM2 button action and is

turned on, the output turns off when any area is disarmed.

When the output action is steady, pulse or toggle and the output is turned on, the

output remains on until:

— the output cutoff time expires

— the output is reset from the keypad menu

— toggled off

NOTE: All wireless programming is stored in the XRSuper6, XR20, or XR40 panel. The 1100D Wireless

Receiver obtains the necessary programming information from the panel each time the receiver powers

up, when the programmer STOP routine is selected or the panel is reset. The receiver memory refresh

takes up to 45 seconds to complete depending on the number of wireless zones programmed and the

Red LED remains on during this time. Normal receiver operation is inhibited during the memory refresh

period.

1 2 ... 34 35 36 37 38 39 40 41 42 43 44 ... 51 52

Comentários a estes Manuais

Sem comentários

Digital Monitoring Products XR20 Guia de Instalação Página 39

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digital Monitoring Products XR20