Digital Monitoring Products XR550 Manual de Instruções descarregar pdf (Página 23)

XR150/XR350/XR550 Series Programming Guide Digital Monitoring Products

MESSAGING SETUP

Messaging Setup

5.1 Messaging Setup

This section allows you to enter the information needed to receive messages directly

from the panel via MyAccess™ SMS Text using Cellular communication. All of the name and

password options below allow up to 32 lowercase characters to be entered. The Destination

addresses allow up to 48 characters to be entered. System Name is displayed with initial

caps.

The transmitted messages are:

• Zone Alarms by Zone Name

• Zone Troubles by Zone Name

• Zone Bypass by User

• Arming (Closings) by User|

• Disarming (Openings) by User

• Late to Close

• AC Power Trouble and Restoral

• System Low Battery

• Ambush

• Abort, Cancel and Alarm Veried by User

5.2 Enable Messaging

Select YES to allow the panel to send messages to three programmed destinations. Default

is NO.

5.3 System Name

Enter a unique name for the panel. The panel name is used as the sender of the message.

The text entered is displayed with initial caps. If this eld is left blank, the panel account

number is sent.

5.4 Destination 1

Enter the rst cell phone number where messages will be sent. The message can be sent to

any device (computer, cell phone, PDA) as long as a valid cell phone number is entered.

5.5 Destination 1 User Number

nter a valid user number from this account. This option is used when sending commands

such as arming or disarming back to the panel using MyAccess™ SMS Text from the same cell

phone or PDA. The user number must have the authority to perform the commands as if it

occurred at the keypad. MyAccess™ SMS Entering 0 (zero) disables this option. Default is 0.

5.6 Destination 2

Enter the second destination cell phone number.

5.7 Destination 2 User Number

Enter a valid User Number for arming/disarming authorization.

5.8 Destination 3

Enter the third destination cell phone number.

5.9 Destination 3 User Number

Enter a valid User Number for arming/disarming authorization.

5.10 O/C SMS

Select YES to allow the panel to send Opening and Closing messages to a cell phone via SMS

protocol. Default is NO. This option displays if any destination is a cell phone number.

5.11 Monthly Limit

This option displays if any programmed destination is a cell phone number using CELL

communication. This number limits the monthly incoming and outgoing SMS messages

allowed to be sent or received by the panel.

A panel event that causes messages to be sent to destination cell phone numbers is counted

towards the panel’s monthly limit. For example, if an alarm message is sent to a cell phone

number, a total of 2 messages are counted towards the monthly limit for the panel. SMS

messages sent from a cell phone to the panel, including status requests and MyAccess™

SMS Text messaging commands, also count toward the monthly limit. The limit is reset at

midnight on the 14th of every month. Range is from 0 to 999. When 0 is entered, there is

no limit on the number of messages able to be sent or received by the panel. Default is 0.

Note: The SecureCom Wireless text plan selected for the panel should match or exceed the

programmed Monthly Limit.

MESSAGING SETUP

ENABLE MESSAGING

NO YES

SYSTEM NAME

DESTINATION 1

USER NUMBER:

DESTINATION 2

USER NUMBER: 0

DESTINATION 3

USER NUMBER: 0

O/C SMS NO YES

MONTHLY LIMIT: 0

1 2 ... 18 19 20 21 22 23 24 25 26 27 28 ... 77 78

Comentários a estes Manuais

Sem comentários

Digital Monitoring Products XR550 Manual de Instruções Página 23

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digital Monitoring Products XR550