Digital Monitoring Products XR550 Manual de Instruções descarregar pdf (Página 26)

Digital Monitoring Products XR150/XR350/XR550 Series Programming Guide

DEVICE SETUP

When an area(s) is chosen, the following displays are allowed:

• Armed Status of the selected area(s)

• Zone Alarms and troubles for burglary (NT, DY, EX, A1, A2) type zones assigned to the

selected area(s)

• Late to Close status of the selected area(s)

• Zone Status (normal/fault) of zones that are assigned to the selected area(s)

Options and Actions Not Affected

The following options are not affected by the Display Areas operation. The User Code

authority level controls access to these items.

• Sensor Reset Menu • Outputs On/Off Menu • System Status Menu

• System Test/Panic Test • User Proles • Forgive Anti-Passback

• Service Request • Set System Time and DatE

• Fire Drill • Display Events

• 24-hour zones display at keypads based on Status List programming only

Note: A common area and its operations cannot be assigned to a specic keypad.

Display Areas example: When Device 1 has Display Areas set to 20, 21, and 22, it

annunciates troubles and alarms only for zones assigned to those areas.

When arming/disarming from Device 1, only areas 20, 21, and 22 may be armed/disarmed,

even when the User Prole has authority to arm/disarm other system areas.

Exception: Disarming of other areas not selected in Display Areas can be accomplished

by presenting a card that has disarming authority and matching prole areas with areas

assigned in Device Access Areas.

6.10 Strike Time

Enter a door access time, between 1 and 250 seconds, during which a keypad or access

control device relay is activated. Magnetic locks or electric door strikes are connected to

the relay and released for the length of the strike time. Default is 5 seconds.

Enter 0 (zero) to activate the device relay with a toggle action. This allows the user to

activate or deactivate the device relay each time a valid user code is entered. The device

relay is activated or deactivated until a user code is entered again.

Note: The Request to Exit door access time of a keypad or Model 734/734N Wiegand

Interface Module is not affected by this selection. It remains at 5 seconds.

6.11 Strike Delay

Enter the number of minutes, 0 to 9, to delay a door strike after a valid code is entered or

a card read occurs. When a valid code or card read or code is received, the activation of

the door strike is delayed for the number of minutes programmed. The standard door strike

message is sent to the Central Station receiver and logged in the Display Events at the

time of card read or code entry and is not delayed. During this delay, all subsequent codes

entered or cards presented to the reader for a door strike are ignored and no record of the

attempt is stored. Enter 0 (zero) to disable. Default is 0 (zero).

6.12 Fire Exit Release

Select YES to allow the door access relay at this address to be released whenever Fire panic

keys are pressed or a Fire or Fire Verify zone alarm is in the Status List. The relay is reset

whenever a Sensor Reset is performed to remove all Fire and Fire Verify zone alarms from the

Status List. Select NO to not allow the door access relay at this address to be released.

6.13 Public Door

Select YES to allow the door access relay at this address to be released whenever the

Lockdown command is issued from the keypad User Menu or remote command. The relay is

reset whenever a Sensor Reset is performed.

Select NO to not allow the door access relay at this address to be released. Default is NO.

6.14 Output Group

Select YES to allow the output group (relays) assigned to the user prole to turn ON when

the device relay is activated for the programmed strike time. This could be used to operate

an elevator control. Default is NO. See the User Proles section in the Appendix of this

document for more information about proles.

6.15 Schedule Override

Use this option to allow door ON/OFF schedules to be overridden by the armed condition

of the system. Selecting YES causes the on time for a door schedule to be ignored when all

areas assigned to Access Areas for this device are armed. Should any area become disarmed

after the door schedule on time, the device output turns on. A door output which is on

during a disarmed period automatically turns off when all access areas assigned to the

device become armed, even if the scheduled off time has not been reached. This feature

can be used to keep doors locked when a factory opens late, or is forced to close early, due

to a snow storm or other cause. Select NO to allow door schedules to operate independent

of system armed status.

STRIKE TIME: 5

STRIKE DELAY: 0

FIRE EXIT NO YES

PUBLIC DR NO YES

OUT GROUP NO YES

OVERRIDE NO YES

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 77 78

Comentários a estes Manuais

Sem comentários

Digital Monitoring Products XR550 Manual de Instruções Página 26

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digital Monitoring Products XR550