Digital Monitoring Products XR550 Manual de Instruções descarregar pdf (Página 68)

Digital Monitoring Products XR150/XR350/XR550 Series Programming Guide

APPENDIX

Note: The panel makes ten attempts to reach the receiver. While attempting to contact the receiver, if the panel

needs to send an alarm report, the panel stops dialing and uses the phone line to send its report.

TEST: The panel allows you to perform a Communication Status Test on each component of the panel’s

cellular or network communication paths. While the Status List displays, enter 984 and press the COMMAND

key. The keypad display changes to NBR TEST PICKUP. Press the Select key under TEST to allow the panel to

perform a Communication Status Test. The display prompts the user for a user code to be entered. The user

code must have the authority to perform a System Test.

Upon entry of a Cell or Network path when prompted, the test runs and the results display on the keypad. See

Diagnostic Functions section for a description of the Communication Status results.

PICKUP: The panel picks up the phone line when Remote Link™ calls in. The phone must be ringing before

selecting PICKUP. After completing panel programming in Remote Link, connect to the panel by selecting

Panel > Connect. Refer to the Remote Link User’s Guide (LT-0565), or Help File for complete information about

connecting to panels.

While the panel displays in the status list and the telephone line at the panel rings, enter 984 and press the

COMMAND key. The keypad display changes to NBR TEST PICKUP. Press the Select key under PICKUP to allow

the panel to seize the line. The panel immediately seizes the phone line and sends a carrier tone to the

receiver. A verication process occurs and, if successful, the panel grants remote access to its programming

and Event Buffer.

After the panel has seized the line, send the le from Remote Link by selecting Panel > Send. Remote Link

then uploads the new programming into the panel. You may also Request Events by selecting Panel > Request

Events in Remote Link. The panel begins sending the rst event or access that occurred on or after the start

date specied by Remote Link and nishes by sending the last event or access that occurred on or before the

end date specied by Remote Link. If necessary, a Request Events upload in progress can be cancelled.

Keypad Displays

When the PICKUP option is used, the keypad displays LINE SEIZED. This indicates that the panel has seized the

line and is executing its program. If the line cannot be accessed, or if the PICKUP option is used before all

connect attempts are made, the keypad displays SYSTEM BUSY.

22.4 Using the Walk Test

The panel provides a walk test feature that allows a single technician to test the protection devices

connected to zones on the system. Conduct the Walk Test within 30 minutes of resetting the panel. The Walk

Test automatically ends if no zones are tripped for 20 minutes. TEST IN PROGRESS displays at all keypads

programmed with the same Display Areas features. When ve minutes remain, TEST END WARNING displays.

The Walk Test only tests zones assigned to the areas programmed into the keypad in Display Areas. If any

areas are armed the Walk Test does not start and SYSTEM ARMED displays.

Note: If the Panic Supervision option is enabled in SYSTEM OPTIONS, the panic button on any programmed key

fob can be tested during the Walk Test. When the panic button is pressed a verication message is sent by the

receiver.

Walk Test

To conduct the Walk Test, reset the control panel by momentarily placing a jumper on J16.

From the keypad, enter the code 8144.

The keypad displays WALK TEST for four seconds. If the system is monitored and the

communication type is DD or NET, the system sends a System Test Begin report to the

central station. After four seconds, the keypad displays the zone type choices for testing.

Zone Types

Select the zone type you want to test. An asterisk next to the zone type indicates the zone

type chosen for testing. Press the Select key again to deselect the zone type. When you

have selected all the zone types you want for testing, press the COMMAND key to display

the next Walk Test option. Pressing the Back Arrow key exits the Walk Test.

Note: For the Wireless Check-in Test, make sure no zone types are selected and press the

COMMAND key. Pressing the Back Arrow key exits the Walk Test.

BG (Burglary zones) - Select BG to test burglary zones. Includes all NT, DY, EX, A1, and A2

zones.

FI (Fire zones) - Select FI to test re zones. Includes all FI and FV zones.

PN (Panic zones) - Select PN to test panic zones. Includes all PN and EM zones.

SV (Supervisory zones) - Select SV to test supervisory zones. Includes all SV zones.

WALK TEST

BG FI PN SV

1 2 ... 63 64 65 66 67 68 69 70 71 72 73 ... 77 78

Comentários a estes Manuais

Sem comentários

Digital Monitoring Products XR550 Manual de Instruções Página 68

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de segurança - controlo de acesso Digital Monitoring Products XR550